EFILive V7.5 and V8
Release Notes
June 2020 - Public Beta Release - 4
Updates and changes since V8.3 public
release - 3
Version Numbers
·
V8 Software: V8.3.1
·
V7.5 Software: V7.5.30
·
FlashScan/AutoCal V3
Firmware: V3.00.044 (June 30, 2020)
·
FlashScan/AutoCal V2
Firmware: V2.07.163 (June 24, 2020), Boot Block: V2.07.008 (July 4, 2018)
EFILive V8
Enhancements:
Beta 48-4
·
When an AutoCal configured to self-sign reads either an E54 (LB7) or an E60
(LLY) controller, the tune file is now self-signed with the correct serial
numbers.
·
The "Clear DTCs" procedure at the end of the read/flash operation
has been updated.
·
Save/Save As are now enabled by default in the [F6: Devices] tab page after
reading the device settings from a FlashScan or AutoCal device.
·
Cummins HD pass-thru data logging would log corrupt data if invalid PIDs
were selected.
·
Cummins HD pass-thru data logging would always fail to start with "no
controllers detected" error.
Beta 48-3
·
Replaced
USBView.exe utility with the more comprehensive USBTreeView.exe in the
Drivers\Utilities folder.
Beta 48-2
·
TCM
licensing is now free for both V2 and V3 devices.
·
FlashScan/AutoCal
V3 VIN license slot count has been increased from 221 to 600.
·
Individual
windows can now be managed more easily via the Windows Task Bar - or via new
drop down button menus in the lower left corner, or via hotkeys.
·
Software
registration is not required.
·
Manage
customer details per vehicle and use customer details in scan and tune file
name templates.
·
User
defined calibrations conversion process from V7 *.cax file format to V8 *.cax8
format.
·
User
defined script conversion process from V7 *.txt format to V8 *.Lua format.
·
V3
devices can be configured to appear as a USB thumb drive in Windows Explorer,
allowing file transfers and management to be performed without installing the
EFILive software.
·
Tune file
editor is available for selected controllers and operating systems:
·
Tune file
comparison between different operating systems.
·
Scan and
tune file linking is now supported.
·
V3
devices support black box data logging without upgrading to CSP5.
·
Dodge
Cummins FAST CAN mode can be configured as a device setting.
·
Custom,
user defined menu systems can be created for V3 devices.
·
The
EFILive EULA is displayed and must be accepted each time a V3 device is powered
on before it can be used in standalone mode.
·
AutoCal's
linked/unlinked status is displayed at the bottom of the EULA screen.
·
Transferring
files to/from V3 devices is up to 10 times faster than V2 devices.
·
And many
more...
Bug
Fixes:
Beta 48-3
·
Updated
OBD error codes and messages in the $0300..$03FF range.
Beta 48-2
·
Fixed CMC
checksum issue.
·
E54 (LB7)
and E60 (LLY) serial numbers are now shown in the [F4: OBD] window.
·
CMF VIN
change is now supported in [F4: OBD]->[VIN Change].
·
Disabled hotkeys
for editing tune files when no tune file is open and/or when no *.cam file is
present for the open tune file.
·
Additional
USB message management to mitigate the $0101 error that may occur on some USB
configurations.
·
Tune
files from A40 controllers that identify as "A46" can now be opened
the V8 software.
·
Selecting
the "Next Scan/Tune Window" (hotkey Alt+F2 and Alt+F3) would cause
the next window to be restored to its un-maximized size if it had been
previously maximized.
Known Issues:
·
When
logging DMA PIDs (i.e. PIDs whose names end with "_M" or
"_DMA"), if the ignition is switched off for an extended period while
data logging but data logging is not terminated, then when the ignition is
switched on again the data log automatically continues. However, the DMA PIDs
may no longer return valid data.
Workaround: EFILive
recommends stopping the data log and restarting the data log when switching off
the ignition for extended periods.
EFILive V7.5
Calibration Updates:
Dodge Cummins
·
New support and updates to
existing operating systems for the following controllers: CME and CMF.
Cummins Heavy Duty
·
New support and updates to
existing operating systems for the following controllers: CM2350A.
GM Gas
·
New support and updates to
existing operating systems for the following controllers: E39, E78, E80, E84
and E92.
GM Diesel
·
New support and updates to
existing operating systems for the following controllers: E98.
Transmission
·
New support for the
following controllers: T76.
Enhancements:
·
None.
Bug Fixes:
·
None.
Known Issues:
·
None.
FlashScan/AutoCal V2
Enhancements:
·
None.
Bug Fixes:
(V2.07.163)
·
Update to
ensure all TCM controllers do not require a VIN license to be flashed.
(V2.07.162)
·
Fixed
slow black box flashing.
Known Issues:
·
None.
FlashScan/AutoCal V3
Enhancements:
·
None.
Bug Fixes:
(V3.00.044)
·
Fixed "Clear DTC" option not working on VPW based controllers.
·
When CVN Data or CVN History is not successfully retrieved from the
controller a more user-friendly message is now displayed - instead of error
$0281 "No data retrieved".
·
Word wrapping for different font sizes is now handled correctly so that
some letters at the start and/or end of lines are not truncated.
(V3.00.043)
·
To
protect the integrity of files on the device, any attempt to read, modify or
delete any file or folder using EFILive_Explorer.exe while a black box
operation (read, flash or data logging) is in progress, will be rejected with
the error $010C "Device is busy".
·
Update to
ensure all TCM controllers do not require a VIN license to be flashed.
(V3.00.042)
·
E45 (LB7)
and E60 (LLY) serial numbers are now shown on the V3 screen when selecting:
Diagnostics -> F1: Display Info -> F1: Display VIN/Info.
Known Issues:
·
None.
Documentation Updates
·
EFILive Error Codes.pdf.
Knowledgebase Updates
·
None.